04-20-2013, 08:48 PM
Steps to install HH Motor
-----------------------------------------------Page 1-----------------------------------------
1-1) Find an appropriate for installation first.
1-2) Make sure there is no obstacle in the sout sky such as tree or toll biilding.
1-3) Make sure the mounting pole is exactly leveled in vertical.
1-4) Fix the h-h motor on the mounting pole and attach the antenna dish on to the motor pole.
1-5) Make sure the center of the antenna dish is with the center of the motor well.
1-6) Make motor elevation at 52*.
1-7) make antenna dish scale 38* approximately.
1-8) Tide all bolts and nuts. (not very tide)
1-9) Make coaxial RG6 cable connection . (see manual book)
1-10) Draw the coaxial RG6 cable as close as possible to the mounting pole to prevent from any
interference between antenna dish bracket and coaxial cable.
1-11) Rotate the motor all together with the antenna dish true south by hand.
---------------------------------------------------o-------------------------------------------
MAKE SETTINGS
-------------------------------------------------PAGE 2----------------------------------------
2-1) Switch on your digital box receiver.
2-2) Put on hotbird 13*E channel. (RAI1,2,3)
Note: Thes is HUMAX settings other receivers are similar, manual settings apply for all.
2-3) (1) press menu (2) installation (3) service searching (4) antenna settings
(5) antenna alternative (6) antenna alternative (7) make DISEqC command mode user.
2-4) press west button for four times(4 seconds in between)
press exit end ok to store changed settings press menu to exit .
2-5) (1) press menu (2) installation (3) status (4) signal quality.
2-6) By hand rotate the motor all together with antenna dish to find the signal from west to east
slowly slowly and get the bast signal quality.
2-7) Tight the motor bracket very well.
2-8) Now tilt the antenna dish up and down and get the highest signal quality.
2-9) Tide the antenna dish bracket very well.
2-10) Now motor is all ready set
---------------------------------------------------o----------------------------------------------
SETTINGS WITH OTHER SAT
-------------------------------------------------Page 3--------------------------------------------
3-1) put on astra 19.2*E channel taquilla or other.
3-2) (1) Press menu (2) installation (3) service searching (4) antenna settings
(5) antenna alternative (6) antenna alternative (7) make DISEqC command mode installer.
3-3) On movement press east or west by pressing left or right from your remote.
3-4) When you see the signal stop rotate immediately by press up or down left or right.
3-5) Chang DISEqC command from installer to user, pulls back slowly slowly
until get the best signal press exit and ok to store changes.
----------------------------------------------------o-----------------------------------------------
3-6) To set another sat all you have to do is the same like page 3 the different is the sat
for example eutelsat w2 16*E.
----------------------------------------------------o-----------------------------------------------
NOTE: YOU CAN ALMOST DRIVE THE MOTOR EAST/WEST VIA MANUAL BUTTON ON THE BOTTOM OF THE MOTOR
(SEE MANUAL BOOK)
-----------------------------------------------Page 1-----------------------------------------
1-1) Find an appropriate for installation first.
1-2) Make sure there is no obstacle in the sout sky such as tree or toll biilding.
1-3) Make sure the mounting pole is exactly leveled in vertical.
1-4) Fix the h-h motor on the mounting pole and attach the antenna dish on to the motor pole.
1-5) Make sure the center of the antenna dish is with the center of the motor well.
1-6) Make motor elevation at 52*.
1-7) make antenna dish scale 38* approximately.
1-8) Tide all bolts and nuts. (not very tide)
1-9) Make coaxial RG6 cable connection . (see manual book)
1-10) Draw the coaxial RG6 cable as close as possible to the mounting pole to prevent from any
interference between antenna dish bracket and coaxial cable.
1-11) Rotate the motor all together with the antenna dish true south by hand.
---------------------------------------------------o-------------------------------------------
MAKE SETTINGS
-------------------------------------------------PAGE 2----------------------------------------
2-1) Switch on your digital box receiver.
2-2) Put on hotbird 13*E channel. (RAI1,2,3)
Note: Thes is HUMAX settings other receivers are similar, manual settings apply for all.
2-3) (1) press menu (2) installation (3) service searching (4) antenna settings
(5) antenna alternative (6) antenna alternative (7) make DISEqC command mode user.
2-4) press west button for four times(4 seconds in between)
press exit end ok to store changed settings press menu to exit .
2-5) (1) press menu (2) installation (3) status (4) signal quality.
2-6) By hand rotate the motor all together with antenna dish to find the signal from west to east
slowly slowly and get the bast signal quality.
2-7) Tight the motor bracket very well.
2-8) Now tilt the antenna dish up and down and get the highest signal quality.
2-9) Tide the antenna dish bracket very well.
2-10) Now motor is all ready set
---------------------------------------------------o----------------------------------------------
SETTINGS WITH OTHER SAT
-------------------------------------------------Page 3--------------------------------------------
3-1) put on astra 19.2*E channel taquilla or other.
3-2) (1) Press menu (2) installation (3) service searching (4) antenna settings
(5) antenna alternative (6) antenna alternative (7) make DISEqC command mode installer.
3-3) On movement press east or west by pressing left or right from your remote.
3-4) When you see the signal stop rotate immediately by press up or down left or right.
3-5) Chang DISEqC command from installer to user, pulls back slowly slowly
until get the best signal press exit and ok to store changes.
----------------------------------------------------o-----------------------------------------------
3-6) To set another sat all you have to do is the same like page 3 the different is the sat
for example eutelsat w2 16*E.
----------------------------------------------------o-----------------------------------------------
NOTE: YOU CAN ALMOST DRIVE THE MOTOR EAST/WEST VIA MANUAL BUTTON ON THE BOTTOM OF THE MOTOR
(SEE MANUAL BOOK)